Southwestern Florida, Florida Plumbing

Although it may always become necessary to hire a professional Southwestern Florida plumber in many cases, the following tips are provided as a first line of defense against common plumbing problems such as noisy pipes, clogged drains or leaks.

Noise in the Pipes

A series of noises may be produced in the pipes, ranging from a loud hammering sound to high-pitched squeaks. Such causes could be loose pipes, water logged air chambers, or high water pressure. When the pipes aren't anchored properly, this may be the cause. Pipes are generally anchored with pipe straps every 6-8 feet for horizontal runs, eight to ten feet for vertical. If your pipes bang when you turn on the water, you may need to add straps and/or cushion the pipes with a rubber covering. A good rule of thumb is to never use galvanized straps on copper pipes or tubing. If a pipe has a faulty air chamber, this typically occurs in lengths of pipes installed behind fixtures and appliances. These pipes hold air that cushions the shock when flowing water is turned off. If they get filled with water, they become less effective. To restore air back into the chambers, turn off the main shutoff water valve and open all the faucets to drain the system. Close the faucets and then turn on the water. This should allow the air chambers to fill with air. Do not ignore a banging water hammer. It can do considerable damage to the hot and cold pipe system in your house.

Clogged Drains

The first thing to check with a drain that is clogged is that the tub's pop-up stopper is widely opened and is free of hair and debris. If the stopper isn't the problem, then the drainpipe is likely clogged. First, try a plunger or chemical drain cleaner. The plunger is useful to clear clogs in most fixtures and should be readily available. If these fail to get the job done, you'll have to clear the trap with a snake or cable augur. This is a long, flexible steel cable wound around a spool that's fitted with a hand crank. A closet augur is specially made for snaking out toilets. It is similar to a cable augur, but the cable is sheathed in a stiff shaft. It is designed to fit through the tight curves of a toilet trap. Most tubs have a P trap in the drain. In some homes, the tub may have a drum trap in the floor near the tub instead (it will have a removable metal cover and a rubber gasket). Using a snake in a tub P trap is very much like snaking out a sink trap. If you have a drum trap, first try snaking it clear through the tub overflow. If that does not work, bailout all the standing water from the tub. Then, using an adjustable-end wrench, unscrew the trap cover slowly. Have rags ready for any water that wells up. Remove the cover, bail out and clean the trap. If, water does not well up, snake toward he tub; if water does well up, snake toward he main drain. If you can not reach the clog from the trap, it's probably deeper in he main drain. At this point, you should enlist the services of a professional plumber.

Leaking Pipes

If your water bill is higher than normal, this may be your first warning of a leaking pipe. You might also hear the sound of running water even when all your fixtures are turned off. When you suspect a leak, check the fixtures first to make sure all the faucets are tightly closed. Then go to the water meter, if you have 1. If the dial is moving, you're losing water somewhere in the system.

Locating the Leak in Your Southwestern Florida Home

The sound of running water helps. If you hear it, follow it to its origination. There are listening devices made to amplify sounds when held up to a pipe. If water is causing stains in the ceiling or dripping down, the leak is likely directly above. Sometimes, water may move along a joist and then stain or drip at a point some distance from the leak. If water stains a wall, it means there is a leak in a portion of the pipe.

Any wall stain is most times under the actual location of the leak and You will most likely need to remove part of the wall to find it. Without the sound of running water and without drips or stains as evidence, leaks are more challenging to find. Using a flashlight, check all the pipes in the basement or in the crawl space.

Correcting the Leak

If the leak is significant, shut off the water immediately, either at the fixture shutoff valve or the main shutoff valve. You'll most likely have to replace the leaky section of pipe. If your experience working with pipes is limited, you'll most likely want to call in an expert plumber to get the job done. If the leak is small, the best solution is to replace the pipe, however there are interim solutions until you've time for the replacement job. These methods work for small leaks only. Clamps ought to stop most leaks for several months if they're used with a solid rubber blanket. It's a smart idea to buy a sheet of rubber padding, as well as some clamps sized to fit your pipes at a hardware store and keep them on hand just for this purpose.

A sleeve clamp that fits exactly the pipe diameter works best. Wrap a rubber blanket over the leak and then screw the clamp down over the blanket. An adjustable hose clamp used with a rubber blanket stops a pinhole leak. If nothing else is available, use a C-clamp, a small block of wood and a rubber blanket.

In a pinch, try applying epoxy putty around a joint where a clamp won't work. The pipe needs to be dry for the putty to adhere. Turn off the water supply to the leak and leave the water off until the putty hardens entirely on the pipe. If you don't have a clamp or putty, you can still stop a small leak provisionally by plugging it with a pencil point.